IBM Computer Monitor P97 User Manual

Color Monitor  
P97  
English  
Operating Instructions  
 
Table of Contents  
Step 1: Connect your monitor to your computer . . . . . . . . . . . . . . . 4  
Step 2: Connect the power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Step 3: Turn on the monitor and computer . . . . . . . . . . . . . . . . . . . 4  
US  
1
 
Use of the Tilt-Swivel  
Precautions  
This monitor can be adjusted within the angles shown below. To  
find the center of the monitors turning radius, align the center of  
the monitors screen with the centering mark on the stand.  
Hold the monitor at the bottom with both hands when you turn it  
horizontally or vertically. Be careful not to pinch your fingers at  
the back of the monitor when you tilt the monitor up vertically.  
Installation  
Do not install the monitor in the following places:  
on surfaces (rugs, blankets, etc.) or near materials (curtains,  
draperies, etc.) that may block the ventilation holes  
near heat sources such as radiators or air ducts, or in a place  
subject to direct sunlight  
in a place subject to severe temperature changes  
in a place subject to mechanical vibration or shock  
on an unstable surface  
near equipment which generates magnetism, such as a  
transformer or high voltage power lines  
15°  
5°  
90°  
90°  
near or on an magnetically charged metal surface  
in a dusty or smoky environment  
into a wall or enclosure  
in a small space that does not allow adequate ventilation around  
the top, bottom, and sides of the monitor that may block the  
ventilation holes  
Centering mark  
Important information on power connection  
Protection  
Use the supplied power cord. If you use a different power cord,  
Do not put foreign objects into the monitor.  
be sure that it is compatible with your local power supply.  
Disconnect the monitor if environment exceeds 60°C/140°F.  
Ensure AC power cord is not trapped under furniture, TV, etc.  
Do not overload wall outlets, extension cords, or convenience  
receptacles beyond their capacity.  
Example of plug types:  
US  
Maintenance  
Clean the screen with a soft cloth. If you use a glass cleaning  
liquid, do not use any type of cleaner containing an anti-static  
solution or similar additive as this may scratch the screens  
coating.  
Do not rub, touch, or tap the surface of the screen with sharp or  
abrasive items such as a ballpoint pen or screwdriver. This type  
of contact may result in a scratched picture tube.  
Clean the cabinet, panel and controls with a soft cloth lightly  
moistened with a mild detergent solution. Do not use any type  
of abrasive pad, scouring powder, or solvent, such as alcohol or  
benzine.  
for 100 to 120 V ac  
for 200 to 240 V ac  
for 240 V ac only  
Before disconnecting the power cord, wait at least 30 seconds  
after turning off the power to allow the static electricity on the  
screens surface to discharge.  
After the power is turned on, the screen is demagnetized  
(degaussed) for a few seconds. This generates a strong  
magnetic field around the screen which may affect the data  
stored on magnetic tapes and diskettes place near the monitor.  
Be sure to keep magnetic recording equipment, tapes, and  
diskettes away from this monitor.  
Transportation  
When you transport this monitor for repair or shipment, use the  
original carton and packing materials.  
Install the equipment near an easily accessible electrical  
outlet.  
2
 
 
Identifying parts and controls  
See the pages in parentheses for further details.  
Front  
Rear  
5
6
1 6m (contrast/down) and M (brightness/up)  
5 AC input connector (page 4)  
This connector provides ac power to the monitor.  
These buttons are used to display the BRIGHT/CONTRAST  
menu and to highlight the desired menu item.  
6 Video input connector (HD15) (page 4)  
This connector inputs RGB video signals (0.700 Vp-p,  
positive) and sync signals.  
US  
2
This button is used to display the menu and to select the menu  
item and to activated the adjustment.  
5
1 2 3 4  
6
7 8 9 10  
3 </, buttons  
11 12 13 14 15  
(pages 5 12)  
These buttons are used to make the adjustment.  
Pin No.  
Signal  
Pin No. Signal  
This button turns the monitor on and off. The power indicator  
lights up in green when the monitor is turned on, and lights up  
in orange when the monitor is in power saving mode.  
1
2
Red  
8
Blue Ground  
DDC + 5V*  
Ground  
Green  
(Sync on  
Green)  
9
10  
11  
12  
ID (Ground)  
3
4
5
6
7
Blue  
Bi-Directional  
Data (SDA)*  
ID (Ground)  
DDC Ground*  
Red Ground  
Green Ground  
13  
14  
15  
H. Sync  
V. Sync  
Data Clock  
(SCL)*  
* Display Data Channel (DDC) Standard of VESA  
3
 
 
Step 2:Connect the power cord  
Setup  
With the monitor and computer turned off, first connect the proper  
power cord for your local supply to the monitor, then connect it to  
a properly grounded power outlet.  
This monitor works with platforms running at horizontal  
frequencies between 30 and 107 kHz.  
Step 1:Connect your monitor to  
your computer  
Turn off the monitor and computer before connecting.  
Notes  
Do not touch the pins of the video signal cable connector as this might  
bend the pins.  
When connecting the video signal cable, check the alignment of the  
video input connector. Do not force the video input connector in the  
wrong way or the pins might bend.  
to AC input  
to a power outlet  
power cord  
Step 3:Turn on the monitor and  
computer  
US  
First turn on the monitor, then turn on the computer.  
To a computer with  
an HD15 video output  
The installation of your monitor is complete.  
If necessary, use the monitors controls to adjust the picture.  
If no picture appears on your screen  
Check that the monitor is correctly connected to the computer.  
If NO SIGNAL appears on the screen, confirm that your  
computers graphics board is completely seated in the correct  
bus slot.  
If you are replacing an old monitor with this model and OUT  
OF SCAN RANGE appears on the screen, reconnect the old  
monitor. Then adjust the computers graphics board so that the  
horizontal frequency is between 30 107 kHz and the vertical  
frequency is between 48 170 Hz.  
4
 
       
Workplace Preparation  
Customizing Your Monitor  
You can make numerous adjustments to your monitor using the  
Positioning the Monitor  
Choose a suitable place to position the monitor where it is not near  
fluorescent desk lighting or any equipment that produces  
magnetic fields that could cause interference.  
Ensure that the furniture or equipment can support the weight of  
the monitor. Allow at least 2 in. (50 mm) ventilation space around  
the monitor.  
on-screen menu.  
Navigating the menu  
x Using the , m/M, and </, buttons  
Height  
The monitor should be positioned so that the top of the screen is  
slightly below your eye level when you sit at your workstation.  
1
Display the menu.  
Press the button to display the menu on the screen.  
Orientation  
EX I T  
Choose a position that gives the least reflection from lights and  
windows, usually at a right angle to any windows. Position the  
monitor directly in front of you so that you do not have to twist  
your body. Tilt the monitor to a comfortable viewing angle.  
45  
1280x1024 / 85Hz  
Working Practices  
2
Select the menu you want to adjust.  
Highlight the desired menu by pressing the m/M buttons.  
Rest  
Take regular breaks. Vary your posture, and stand up and stretch  
occasionally as prolonged use of computer workstations can be  
tiring.  
Then press the  
button.  
US  
Back  
Sit back in the chair and use the backrest.  
Hands  
Use a light touch on the keyboard, keeping your hands and fingers  
relaxed. Allow a space in front of the keyboard to rest your wrists  
when not typing. Consider using a wristpad.  
3
Adjust the menu.  
Press the </, buttons to make the adjustment, then press  
the  
button to activate the adjustment.  
Eyesight  
Working with monitors, in common with any kind of prolonged  
close work, can be visually demanding. Look away from the  
screen periodically and have your eyesight checked regularly.  
Screen settings  
Set the screen brightness and contrast to a comfortable level.  
You may have to adjust this as the lighting changes during the  
day. Many application programs let you select color combinations  
which can help you to view in comfort.  
If you want to select another menu:  
Press the m/M buttons to select  
and press the  
button to  
exit the menu.  
4
Close the menu.  
Each time you select  
and press the  
button, the menu  
exits. If no buttons are pressed, the menu closes automatically  
after about 30 seconds.  
(continued)  
5
 
       
x Selecting the on-screen menu language  
x Menu items  
(LANGUAGE)  
EXIT  
Close the menu.  
English, French, German, Spanish, Italian, Dutch, Swedish,  
Russian, and Japanese versions of the on-screen menus are  
available.  
BRIGHT/CONTRAST  
BR I GHT /CONTRAST  
BR I GHTNESS  
1
Press the  
button.  
Adjusts the brightness and  
contrast. You can call up  
this menu directly by  
50  
EX I T  
pressing the  
buttons while there is no  
menu on the screen.  
M or 6 m  
1280x1024 / 85Hz  
45  
1280x1024 / 85Hz  
Adjusts the size and  
centering.  
S I ZE / CENTER  
2
Press the m/M buttons to highlight  
press the button.  
OPTION and  
45  
1280x1024 / 85Hz  
OPT I ON  
Adjusts the rotation and  
shape of the picture.  
GEOMETRY  
CONTROL  
LOCK  
ON  
OFF  
45  
1280x1024 / 85Hz  
1280x1024 / 85Hz  
3
Press the m/M buttons to highlight  
and press the button.  
(LANGUAGE)  
US  
CONVERGENCE  
CONVERGENCE  
Adjusts the pictures  
horizontal and vertical  
convergence.  
T
B
OPT I ON  
45  
LANGUAGE  
ENGL I SH  
FRANÇA I S  
DEUTSCH  
1/3  
1280x1024 / 85Hz  
SCREEN (page 10)  
Adjusts the pictures  
quality.  
SCREEN  
1280x1024 / 85Hz  
DEGAUSS  
4
Press the m/M buttons until the desired language  
The options include:  
degaussing the screen  
(DEGAUSS)  
adjusting the moire  
cancellation (CANCEL  
MOIRE)  
OK  
appears on the screen. Then press the  
select the language.  
button to  
CANCEL  
1280x1024 / 85Hz  
Each time you press the m/M buttons, the languages that can  
be selected appear cyclically.  
ENGLISH  
FRANÇAIS: French  
DEUTSCH: German  
:
PRESET  
COLOR  
Adjusts the pictures color  
temperature to match the  
monitors colors to a printed  
pictures colors.  
ESPAÑOL: Spanish  
ITALIANO: Italian  
NEDERLANDS: Dutch  
SVENSKA: Swedish  
9 3 0 0 K  
6 5 0 0 K  
5 0 0 0 K  
: Russian  
: Japanese  
1280x1024 / 85Hz  
To close the menu  
Press the m/M buttons to select  
closes automatically after about 30 seconds.  
. If no buttons are pressed, the menu  
(continued)  
6
 
 
OPTION (page 12)  
Adjusts the monitors  
options.  
The options include:  
locking the controls  
changing the on-screen  
menus language  
OPT I ON  
Adjusting the brightness and  
contrast (BRIGHT/CONTRAST)  
CONTROL  
LOCK  
ON  
OFF  
These settings are stored in memory for all signals.  
1280x1024 / 85Hz  
1
2
Press the  
M button to call up the BRIGHTNESS  
adjustment window, or press the 6 m button to call  
up the CONTRAST adjustment window.  
changing the on-screen  
menu position  
RESET  
Press the </, buttons to adjust the brightness  
Resets the adjustments.  
1
2
(
) or contrast (6).  
CURRENT  
MODE  
If you are using the sRGB mode  
OK  
CANCEL  
If you selected the sRGB mode in the COLOR MODE ( ) of the  
COLOR ( ) menu, the following BRIGHT/CONTRAST menu  
appears on the screen.  
1280x1024 / 85Hz  
x Displaying the current input signal  
BR I GHT /CONTRAST  
sRGB  
When you press the  
button to display the menu, information  
on the current input signal is displayed. If the current input signal  
matches one of the monitors factory preset modes, the resolution  
and vertical frequencies are displayed. (See page 18 for a list of  
factory preset modes.) If the current input signal does not match  
one of the factory presets, the horizontal and vertical frequencies  
are displayed.  
:
/
1280x1024 / 85Hz  
You cannot adjust the contrast (6) nor brightness ( ) on this  
screen. If you want to adjust them, select a mode other than sRGB  
in the COLOR MODE ( ) of the COLOR ( ) menu.  
EX I T  
US  
For more information about using the sRGB mode, see  
45  
the vertical  
frequencies of  
the current  
input signal  
1280x1024 / 85Hz  
the resolution/horizontal  
frequencies of the current input  
signal  
7
 
 
Adjusting the centering of the  
picture (SIZE/CENTER)  
Automatically sizing and centering  
the picture (AUTO)  
This setting is stored in memory for the current input signal.  
You can easily adjust the picture to fill the screen by using the  
SIZE/CENTER menu.  
1
2
Press the  
The menu appears on the screen.  
button.  
1
2
Press the  
The menu appears on the screen.  
button.  
Press the m/M buttons to highlight  
and press the  
The SIZE/CENTER menu appears on the screen.  
SIZE/CENTER  
button.  
Press the m/Mbuttons to highlight  
and press the  
SIZE/CENTER  
button.  
The SIZE/CENTER menu appears on the screen.  
3
4
Press the m/M buttons to select  
adjustment, or for vertical adjustment. Then  
button.  
for horizontal  
3
4
Press the m/M buttons to select  
press the button.  
The adjustment window appears on the screen.  
(AUTO). Then  
press the  
Press the </, buttons to adjust the centering.  
Press the m/M buttons to select OK.  
The picture automatically fills the screen.  
Adjusting the size of the picture  
(SIZE/CENTER)  
This setting is stored in memory for the current input signal.  
1
2
Press the  
The menu appears on the screen.  
button.  
Notes  
US  
If you do not want to use the AUTO function, select CANCEL in step 4.  
This function is intended to be used when the computer is displaying  
what should be a full-screen picture. It may not work properly if the  
background color is dark or if the input picture does not fill the screen  
to the edges.  
Press the m/M buttons to highlight  
and press the  
The SIZE/CENTER menu appears on the screen.  
SIZE/CENTER  
button.  
The displayed image moves for a few seconds while this function is  
performed. This is not a malfunction.  
3
4
Press the m/M buttons to select  
adjustment, or for vertical adjustment. Then  
button.  
for horizontal  
press the  
Press the </, buttons to adjust the size.  
8
 
     
Adjusting the shape of the picture  
(GEOMETRY)  
Adjusting the convergence  
(CONVERGENCE)  
The CONVERGENCE settings allow you to adjust the quality of  
the picture by controlling the convergence. The convergence  
refers to the alignment of the red, green, and blue color signals.  
If you see red or blue shadows around letters or lines, adjust the  
convergence.  
The GEOMETRY settings allow you to adjust the rotation and  
shape of the picture.  
The  
(rotation) setting is stored in memory for all input signals.  
All other settings are stored in memory for the current input  
signal.  
These settings are stored in memory for all input signals.  
1
2
Press the  
The menu appears on the screen.  
button.  
1
2
Press the  
The menu appears on the screen.  
button.  
Press the m/M buttons to highlight  
and press the  
The GEOMETRY menu appears on the screen.  
GEOMETRY  
Press the m/M buttons to highlight  
button.  
CONVERGENCE and press the  
button.  
The CONVERGENCE menu appears on the screen.  
3
4
Press the m/M buttons to select the desired  
3
4
Press the m/M buttons to select the desired  
adjustment item. Then press the  
button.  
adjustment item. Then press the  
button.  
The adjustment bar appears on the screen.  
The adjustment bar appears on the screen.  
Press the </, buttons to make the adjustment.  
Press the </, buttons to make the adjustment.  
Select  
To  
Select  
To  
rotate the picture  
horizontally shift red or blue shadows  
expand or contract the picture sides  
US  
vertically shift red or blue shadows  
shift the picture sides to the left or right  
adjust the picture width at the top of the screen  
vertically shift red or blue shadows at the top of  
the screen  
T
TOP  
shift the picture to the left or right at the top of the  
screen  
vertically shift red or blue shadows at the bottom  
of the screen  
B
BOTTOM  
0
RESET  
reset all the GEOMETRY adjustments to the  
factory setting levels. Select OK.  
0
RESET  
reset all the CONVERGENCE adjustments to  
the factory setting levels. Select OK.  
For more information about using the RESET mode, see  
For more information about using the RESET mode, see  
9
 
   
Adjusting the picture quality  
(SCREEN)  
Adjusting the color of the picture  
(COLOR)  
The SCREEN settings allow you to degauss (demagnetize) the  
monitor manually and adjust the picture quality by controlling the  
moire.  
• If the color is not uniform or the picture is fuzzy, degauss the  
monitor (DEGAUSS).  
The COLOR settings allow you to adjust the picture’s color  
temperature by changing the color level of the white color field.  
Colors appear reddish if the temperature is low, and bluish if the  
temperature is high. This adjustment is useful for matching the  
monitor’s color to a printed picture’s colors.  
• If elliptical or wavy patterns appear on the screen, cancel the  
moire (CANCEL MOIRE).  
The monitor is automatically demagnetized (degaussed) when the  
power is turned on.  
The screen is degaussed for about 2 seconds. If a second degauss  
cycle is needed, allow a minimum interval of 20 minutes for the  
best result.  
x Select the COLOR mode  
There are 4 types of adjustment modes, PRESET, VARIABLE,  
EXPERT, and sRGB. The default setting is PRESET mode which  
can be adjusted to 9300K, 6500K, or 5000K.  
If you want to set another mode (other than PRESET), select the  
desired mode in the COLOR ( ) menu. Then adjust the selected  
mode in each COLOR MODE ( ) menu.  
The CANCEL MOIRE setting is stored in memory for the current  
input signal.  
1
2
Press the  
The menu appears on the screen.  
button.  
1
2
Press the  
The menu appears on the screen.  
button.  
Press the m/M buttons to highlight  
press the  
COLOR and  
(COLOR  
button.  
Press the m/M buttons to highlight  
press the  
SCREEN and  
The COLOR menu appears on the screen.  
button.  
The SCREEN menu appears on the screen.  
3
4
Press the m/M buttons to highlight  
MODE). Then press the  
button.  
US  
3
4
Press the m/M buttons to select the desired  
adjustment item. Then press the  
button.  
Press the m/M buttons to select the COLOR mode.  
The adjustment bar appears on the screen.  
:
COLOR  
PRESET  
Press the m/M or </, buttons to make the  
adjustment.  
COLOR MODE  
PRESET  
VARIABLE  
EXPERT  
sRGB  
Select  
DEGAUSS  
To  
1280x1024 / 85Hz  
degauss the monitor. To degauss the monitor  
manually, select OK.  
adjust the degree of moire cancellation until  
the moire* is at a minimum  
5
Press the  
button three times to close the menu.  
CANCEL  
MOIRE  
*
Moire is a type of natural interference which produces soft, wavy lines  
on your screen. It may appear due to interference between the pattern  
of the picture on the screen and the phosphor pitch pattern of the  
monitor.  
Example of moire  
Note  
The picture may become fuzzy when the CANCEL MOIRE function is  
activated.  
(continued)  
10  
 
       
x PRESET mode  
x EXPERT mode  
You can make additional adjustments to the color in greater detail  
1
Press the  
The menu appears on the screen.  
button.  
by selecting the EXPERT mode.  
1
2
Press the  
The menu appears on the screen.  
button.  
2
Press the m/M buttons to highlight  
COLOR and  
. Then press  
press the  
button.  
The COLOR menu appears on the screen.  
Press the m/M buttons to highlight  
press the  
COLOR and  
button.  
3
Press the m/M buttons to highlight  
:
COLOR  
EXPERT  
the  
button.  
R
G
B
R
G
B
:
COLOR  
PRESET  
45  
1280x1024 / 85Hz  
9 3 0 0 K  
6 5 0 0 K  
5 0 0 0 K  
1280x1024 / 85Hz  
3
Press the m/M buttons to select the R (red), G  
(green), or B (blue) and press the  
press the </, buttons to adjust the input signal  
for both GAIN (6) and BIAS ( ).  
button. Then  
4
Press the m/M buttons to select the desired  
temperature.  
If you want to reset the EXPERT adjustments, select  
0(RESET) in COLOR menu. Then select OK in the RESET  
window.  
The preset color temperatures are 9300K, 6500K, and 5000K.  
Since the default setting is 9300K, the whites will change  
from a bluish hue to a reddish hue as the temperature is  
lowered to 6500K and 5000K.  
x sRGB mode  
x VARIABLE mode  
The sRGB color setting is an industry standard color space  
protocol designed to correlate the displayed and printed colors of  
sRGB compliant computer products. To adjust the colors to the  
sRGB profile, simply select the sRGB mode in the COLOR  
US  
1
Press the  
The menu appears on the screen.  
button.  
MODE ( ) menu of the COLOR ( ) menu.  
2
Press the m/M buttons to highlight  
COLOR and  
. Then press  
However, in order to display the sRGB colors correctly (γ = 2.2,  
6500K), you must set your computer to the sRGB profile. If you  
select this mode, you cannot operate the BRIGHT/CONTRAST  
menu adjustments.  
press the  
button.  
The COLOR menu appears on the screen.  
3
Press the m/M buttons to highlight  
:
COLOR  
sRGB  
the  
button.  
:
COLOR  
VARIABLE  
5 0 0 0 K  
sRGB  
:
/
1280x1024 / 85Hz  
1280x1024 / 85Hz  
Note  
Your computer and other connected products (such as a printer), must be  
sRGB compliant.  
4
Press the </, buttons to fine tune the color  
temperature.  
The new color temperature setting you fine tuned between  
5000K to 11000K is stored in memory.  
11  
 
 
Additional settings (OPTION)  
Resetting the adjustments (RESET)  
You can lock the controls, change the on-screen language, change  
the menu position.  
This monitor has the following 2 reset methods.  
x Resetting all the adjustment data for the  
1
2
Press the  
The menu appears on the screen.  
button.  
current input signal  
1
2
3
4
Press the  
The menu appears on the screen.  
button.  
Press the m/M buttons to highlight  
OPTION and press the  
The OPTION menu appears on the screen.  
button.  
Press the m/M buttons to highlight  
0 RESET and press the  
button.  
3
Press the m/M buttons to select the desired  
adjustment item.  
Adjust the selected item according to the following  
Press the m/M buttons to select 01 (CURRENT  
MODE) and press the button.  
instructions.  
Press the m/M buttons to select OK.  
x Locking the controls (CONTROL LOCK)  
You can protect the adjustment data by locking the controls.  
RESET  
1
Press the m/M buttons to highlight  
LOCK) and press the button. Then press the m/M  
buttons to select ON and press the button.  
, and  
(CONTROL  
2
CURRENT  
MODE  
OK  
CANCEL  
Only the 1 (power) button,  
(CONTROL LOCK) of the  
any other items are selected, the  
button,  
OPTION menu will operate. If  
mark appears on the screen.  
1280x1024 / 85Hz  
Note that the following items are not reset by this method:  
on-screen menu language (page 6)  
To cancel the control lock  
US  
color mode setting in the COLOR menu (PRESET,  
color temperature setting in the PRESET mode (9300K,  
Repeat the procedure above and set  
(CONTROL LOCK) to OFF.  
x Changing the on-screen language  
(LANGUAGE)  
on-screen menu position (page 12)  
x Resetting all of the adjustment data for all  
x Changing the menus position  
input signals  
(OSD POSITION)  
Change the menus position if it is blocking an image on the  
screen.  
Select 02 (ALL MODES) in step 3 above.  
Press the m/M buttons to select  
for horizontal adjustment, or  
vertical adjustment and press the  
(OSD POSITION)  
(OSD POSITION) for  
button. Then  
Note  
The RESET function does not function when  
is set to ON.  
(CONTROL LOCK)  
press the </, buttons to shift the on-screen menu.  
Then press the button.  
12  
 
             
Technical Features  
Troubleshooting  
Before contacting technical support, refer to this section.  
Preset and user modes  
If thin lines appear on your screen  
(damper wires)  
When the monitor receives an input signal, it automatically  
matches the signal to one of the factory preset modes stored in the  
monitor’s memory to provide a high quality picture at the center  
of the screen. (See page 18 for a list of the factory preset modes.)  
For input signals that do not match one of the factory preset  
modes, the digital Multiscan technology of this monitor ensures  
that a clear picture appears on the screen for any timing in the  
monitor’s frequency range (horizontal: 30 – 107 kHz, vertical: 48  
– 170 Hz). If the picture is adjusted, the adjustment data is stored  
as a user mode and automatically recalled whenever the same  
input signal is received.  
The visible lines on your screen especially when the background  
screen color is light (usually white), are normal for the Trinitron  
monitor. This is not a malfunction. These are shadows from the  
damper wires used to stabilize the aperture grille. The aperture  
grille is the essential element that makes a Trinitron picture tube  
unique by allowing more light to reach the screen, resulting in a  
brighter, more detailed picture.  
Damper wires  
Note for Windows users  
For Windows users, check your graphics board manual or the  
utility program which comes with your graphics board and select  
the highest available refresh rate to maximize monitor  
performance.  
Power saving function  
On-screen messages  
US  
This monitor meets the power-saving guidelines set by VESA and  
ENERGY STAR. If no signal is input to the monitor from your  
computer, the monitor will automatically reduce power  
consumption as shown below.  
If there is something wrong with the input signal, one of the  
following messages appears on the screen.  
If NO SIGNAL appears on section 1  
This indicates that no signal is input.  
Power mode Power consumption 1 (power)  
1
indicator  
I NFORMAT I ON  
normal  
operation  
135 W  
3 W  
green  
orange  
off  
MONI TOR I S WORK I NG  
I NPUT  
: NO S I GNAL  
W
R
G
B
ACT I VATE BY COMPUTER  
CHECK S I GNAL CABLE  
active off*  
(deep sleep)**  
power off  
Approx. 0 W  
2
* When your computer enters power saving mode, the input signal is cut  
and NO SIGNAL appears on the screen before the monitor enters active  
off mode. After a minute, the monitor enters power saving mode.  
**“Deep sleep” is power saving mode defined by the Environmental  
Protection Agency.  
2 The remedies  
The following messages appear on the screen.  
• If ACTIVATE BY COMPUTER appears on the screen, try  
pressing any key on the computer or moving the mouse, and  
confirm that your computer’s graphics board is completely  
seated in the correct bus slot.  
• If CHECK SIGNAL CABLE appears on the screen, check  
that the monitor is correctly connected to the computer  
(page 4).  
(continued)  
13  
 
             
If OUT OF SCAN RANGE appears on line 1  
This indicates that the input signal is not supported by the  
monitors specifications.  
2
1
I NFORMAT I ON  
MONI TOR I S WORK I NG  
I NPUT  
: 200.0kHz/ 85Hz  
W
R
G
B
OUT OF SCAN RANGE  
CHANGE S I GNAL T I MI NG  
3
2 The frequencies of the current input signal  
If the monitor recognizes the frequencies of the current input  
signal, the horizontal and vertical frequencies are also  
displayed.  
3 The remedies  
CHANGE SIGNAL TIMING appears on the screen. If you  
are replacing an old monitor with this monitor, reconnect the  
old monitor. Then adjust the computers graphics board so  
that the horizontal frequency is between 30 107 kHz, and the  
vertical frequency is between 48 170 Hz.  
US  
Displaying this monitors name, serial number,  
and date of manufacture  
While the monitor is receiving a video signal, press and hold the  
button for more than 5 seconds to display this monitors  
information box.  
Example  
INFORMATION  
:
MODEL IBM P97  
:
W
R
G
B
SER NO 12-34567  
: 2001-52  
MANUFACTURED  
If the problem persists, call your authorized technical support and  
give the following information.  
Model name: IBM P97  
Serial number  
Name and specifications of your computer and graphics board  
14  
 
Trouble symptoms and remedies  
If the problem is caused by the connected computer or other equipment, please refer to the connected equipments instruction manual.  
Use the self-diagnosis function (page 17) if the following recommendations do not resolve the problem.  
Symptom  
No picture  
Check these items  
If the 1 (power) indicator is not lit  
Check that the power cord is properly connected.  
Check that the 1 (power) button is in the onposition.  
If the NO SIGNAL message appears Check that the video signal cable is properly connected and all plugs are firmly seated in  
on the screen, or if the  
their sockets (page 4).  
1 (power) indicator is orange  
Check that the video input connectors pins are not bent or pushed in.  
xProblems caused by the connected computer or other equipment  
The computer is in power saving mode. Try pressing any key on the keyboard or moving  
the mouse.  
Check that the computers power is on.”  
Check that the graphic board is completely seated in the proper bus slot.  
If the OUT OF SCAN RANGE  
message appears on the screen  
xProblems caused by the connected computer or other equipment  
Check that the video frequency range is within that specified for the monitor. If you  
replaced an old monitor with this monitor, reconnect the old monitor and adjust the  
frequency range to the following.  
Horizontal: 30 107 kHz  
Vertical: 48 170 Hz  
If no message is displayed and the  
1 (power) indicator is green or  
flashing orange  
Use the Self-diagnosis function (page 17).  
US  
Picture flickers, bounces,  
oscillates, or is scrambled  
Isolate and eliminate any potential sources of electric or magnetic fields such as other  
monitors, laser printers, fluorescent lighting, televisions, or electric fans.  
Move the monitor away from power lines or place a magnetic shield near the monitor.  
Try plugging the monitor into a different AC outlet, preferably on a different circuit.  
Try turning the monitor 90° to the left or right.  
xProblems caused by the connected computer or other equipment  
Check your graphics board manual for the proper monitor setting.  
Confirm that the graphics mode and the frequency of the input signal are supported by this  
monitor (page 18). Even if the frequency is within the proper range, some graphics boards  
may have a sync pulse that is too narrow for the monitor to sync correctly.  
Adjust the computers refresh rate (vertical frequency) to obtain the best possible picture.  
Picture is fuzzy  
Adjust the brightness and contrast (page 7).  
Degauss the monitor* (page 10).  
Adjust the degree of moire cancellation until the moire is minimal, or set CANCEL  
* If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. A humming noise may be heard, but this is not a  
malfunction.  
(continued)  
15  
 
   
Symptom  
Check these items  
Picture is ghosting  
Eliminate the use of video cable extensions and/or video switch boxes.  
Check that all plugs are firmly seated in their sockets.  
Picture is not centered or sized  
properly  
Set the AUTO ( ) function to OK (on) in the SIZE/CENTER menu (page 8).  
Adjust the size or centering (page 8). Note that with some input signals and/or graphics  
boards the periphery of the screen is not fully utilized.  
Edges of the image are curved  
Adjust the geometry (page 9).  
Wavy or elliptical pattern (moire)  
is visible  
Adjust the degree of moire cancellation until the moire is minimal (page 10).  
xProblems caused by the connected computer or other equipment  
Change your desktop pattern.  
Color is not uniform  
Degauss the monitor* (page 10). If you place equipment that generates a magnetic field,  
such as a speaker, near the monitor, or if you change the direction the monitor faces, color  
may lose uniformity.  
White does not look white  
Adjust the color temperature (page 10).  
Letters and lines show red or blue Adjust the convergence (page 9).  
shadows at the edges  
Monitor buttons do not operate  
appears on the screen)  
If the control lock is set to ON, set it to OFF (page 12).  
(
A hum is heard right after the  
power is turned on  
This is the sound of the auto-degauss cycle. When the power is turned on, the monitor is  
automatically degaussed for a few seconds.  
* If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. A humming noise may be heard, but this is not a  
malfunction.  
US  
16  
 
Self-diagnosis function  
Specifications  
This monitor is equipped with a self-diagnosis function. If there is  
a problem with your monitor or computer(s), the screen will go  
blank and the 1 (power) indicator will either light up green or  
flash orange. If the 1 (power) indicator is lit in orange, the  
computer is in power saving mode. Try pressing any key on the  
keyboard or moving the mouse.  
CRT  
0.24 mm aperture grille pitch  
19 in. measured diagonally  
90-degree deflection  
Trinitron  
Viewable image size  
Approx. 365.0 × 274.0 mm (w/h)  
(14 × 11 in.)  
18.0" viewing image  
Resolution  
Maximum  
Horizontal: 1600 dots  
Vertical: 1200 lines  
Horizontal: 1280 dots  
Vertical: 1024 lines  
Video signal  
Recommended  
Input signal levels  
1 (power) indicator  
Analog RGB: 0.700 Vp-p  
(positive), 75 Ω  
SYNC signal  
x If the 1 (power) indicator is green  
H/V separate or composite sync:  
TTL 2 k, Polarity free  
Sync on Green: 0.3 Vp-p  
(negative)  
1
2
3
Disconnect the video input connector from the  
computer, or turn off the connected computer.  
Standard image area  
Deflection frequency*  
4:3  
Press the 1 (power) button twice to turn the monitor  
off and then on.  
Approx. 352 × 264 mm (w/h)  
(13 6/7 × 10 2/5 in.)  
Horizontal: 30 to 107 kHz  
Vertical: 48 to 170 Hz  
Press the M button for 2 seconds before the monitor  
enters power saving mode.  
US  
AC input voltage/current 100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 A  
Power consumption  
Dimensions  
Approx. 135 W  
Approx. 462 × 483 × 469 mm (w/h/d)  
(18 1/4 × 19 1/8 × 18 1/2 in.)  
Approx. 27 kg (59 lb 8.39 oz)  
DDC2B/DDC2Bi, GTF (page 18)  
Mass  
Plug and Play  
* Recommended horizontal and vertical timing condition  
• Horizontal sync width duty should be more than 4.8% of  
total horizontal time or 0.67 µs, whichever is larger.  
If all four color bars appear (white, red, green, blue), the monitor  
is working properly. Reconnect the video input cables and check  
the condition of your computer.  
• Horizontal blanking width should be more than 2.4 µsec.  
• Vertical blanking width should be more than 400 µsec.  
If the color bars do not appear, there is a potential monitor failure.  
Inform your authorized technical support of the monitor’s  
condition.  
Design and specifications are subject to change without notice.  
x If the 1 (power) indicator is flashing orange  
Press the 1 (power) button twice to turn the monitor off  
and then on.  
If the 1 (power) indicator lights up green, the monitor is working  
properly.  
If the 1 (power) indicator is still flashing, there is a potential  
monitor failure. Count the number of seconds between orange  
flashes of the 1 (power) indicator and inform your authorized  
technical support of the monitor’s condition. Be sure to note the  
model name and serial number of your monitor. Also note the  
make and model of your computer and graphic board.  
17  
 
   
x Preset mode timing table  
Service Information  
The following parts are for use by IBM service, or IBM  
authorized dealers, to support customer warranty. Parts are for  
service use only.  
No. Resolution Horizontal Vertical  
Graphics  
(dots ×  
Frequency Frequency Mode  
lines)  
1
2
3
4
5
6
7
8
9
640 × 480  
640 × 480  
720 × 400  
720 × 400  
800 × 600  
800 × 600  
800 × 600  
1024 × 768  
1024 × 768  
31.5 kHz  
43.3 kHz  
31.5 kHz  
37.9 kHz  
37.9 kHz  
46.9 kHz  
53.7 kHz  
48.4 kHz  
56.5 kHz  
60.0 kHz  
68.7 kHz  
67.5 kHz  
77.5 kHz  
60.0 kHz  
85.9 kHz  
60 Hz  
85 Hz  
70 Hz  
85 Hz  
60 Hz  
75 Hz  
85 Hz  
60 Hz  
70 Hz  
75 Hz  
85 Hz  
75 Hz  
85 Hz  
60 Hz  
85 Hz  
60 Hz  
75 Hz  
85 Hz  
60 Hz  
65 Hz  
70 Hz  
75 Hz  
85 Hz  
VGA-G  
VESA  
VGA-Text  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
Monitor Information  
Part No.  
22P7456  
22P7457  
22P7458  
22P7459  
M/T-Model Description  
6651-T3N P97 Monitor - NH (Pearl White)  
6651-U3N P97 Monitor - NH (Stealth Black)  
6651-T3S  
P97 Monitor - SH (Pearl White)  
6651-U3S P97 Monitor - SH (Stealth Black)  
10 1024 × 768  
11 1024 × 768  
12 1152 × 864  
13 1152 × 864  
14 1280 × 960  
15 1280 × 960  
16 1280 × 1024 64.0 kHz  
17 1280 × 1024 80.0 kHz  
18 1280 × 1024 91.1 kHz  
19 1600 × 1200 75.0 kHz  
20 1600 × 1200 81.3 kHz  
21 1600 × 1200 87.5 kHz  
22 1600 × 1200 93.8 kHz  
23 1600 × 1200 106.3 kHz  
US  
If the input signal does not match one of the factory preset modes  
above, the Generalized Timing Formula feature of this monitor  
will automatically provide an optimal image for the screen as long  
as the signal is GTF compliant.  
18  
 
     

Graco Baby Accessories PD121385B User Manual
Hasbro Robotics 81139 User Manual
Hawking Technology Network Card CardBus 10 100 Fast Ethernet PC Card User Manual
Heath Zenith Oven AC 6507 User Manual
Honeywell Home Theater Server w964f User Manual
HP Hewlett Packard All in One Printer X476dw User Manual
Husky Pressure Washer HU80520 User Manual
IBM Computer Hardware 8122 User Manual
IBM Laptop 390E User Manual
Impex Home Gym MP 1100 User Manual